Knowledge Base

Follow

StudioLive Series III - Default AVB Send Assignments for NSB Outputs

Updated July 2, 2021

Before proceeding please be sure your firmware is updated on your respective StudioLive and Universal Control:

StudioLive Series III Console - Firmware Update

StudioLive Series III Rack mixer - Firmware Update

Universal Control:

https://www.presonus.com/products/UC-Surface/downloads

==============================================================

 

While section 14.2.3 of the Studio Live Series III Owners Manual covers default routing of AVB sends, we would like to provide a little more information on how the sends align with an NSB Stagebox and a Series III mixer when assigning "Output Sources" to the NSB in the "Remote I/O Setup" menu.

 

A video demonstration of routing Aux outputs and Main Output to your NSB outputs can be found here:

StudioLive Series III - AVB Output Routing with NSB Stageboxes on StudioLive Series III digital mixers (Video)

 

StudioLive Series III features 8 sets of 8-channel streams (for 64 channels total).

 

When assigned to the NSB "Output Source"-

Stream 1: AVB Sends 1-8 are Channels 1-8 and sent to NSB Outputs 1-8.

  • Pre-DSP, Pre Fader AVB sends.
  • If you wish the output to be post DSP, then on the change the “Digital Send Option” for the channel to be “Post”

Stream 2: AVB Sends 9-16 are Channels 9-16 and sent to NSB Outputs 1-8.

  • Pre-DSP, Pre Fader AVB sends.
  • If you wish the output to be post DSP, then on the change the “Digital Send Option” for the channel to be “Post” 

Stream 3: AVB Sends 17-24 are Channels 17-24 and sent to NSB Outputs 1-8.

  • Pre-DSP, Pre Fader AVB sends.
  • If you wish the output to be post DSP, then on the change the “Digital Send Option” for the channel to be “Post”  

Stream 4: AVB Sends 25-32 are Channels 25-32 and sent to NSB Outputs 1-8.

  • Pre-DSP, Pre Fader AVB sends.
  • If you wish the output to be post DSP, then on the change the “Digital Send Option” for the channel to be “Post”  

Stream 5: AVB Sends 33-40 are assigned as follows:

  • 33-34: Aux input 1L, 2R = Pre-DSP, Pre Fader AVB sends (NSB Outputs 1 & 2)
  • 35-36: Aux input 3L, 4R = Pre-DSP, Pre Fader AVB sends (NSB Outputs 3 & 4)
  • 37-38: Tape In L, Tape In R = Pre-DSP, Pre Fader AVB sends (NSB Outputs 5 & 6)
  • 39-40: Main L, Main R = Post Fader/DSP AVB sends (NSB Outputs 7 & 8)

*NOTE* If you wish the output to be post DSP, change the “Digital Send Option” for the channel to be “Post”

Furthermore:

If you are unable to control the volume of your Auxes or Mains over AVB using their respected Master-Fader, please be sure that your Aux/Mix Master Fader is set to "Post Fader", and not "PreDSP".

  1. Press [Select] on the Aux Master,
  2. Observe the bottom right "Digital Send" section on the Main screen.
  3. Set this option to "Post Fader"
  4. Repeat these steps for all Output mixes.

 

Stream 6: AVB Sends 41-48 are Output Mixes 1-8 and sent to NSB Outputs 1-8.

  • Behaves the same as a normal Aux with Pre/Post and DSP settings

Stream 7: AVB Sends 49-56 are Output Mixes 9-16 and sent to NSB Outputs 1-8.

  • Behaves the same as a normal Aux with Pre/Post and DSP settings

Stream 8: AVB Sends 57-64 are assigned to "None"(Mixes 17 to 24 for the StudioLive 64s)

  • Behaves the same as a normal Aux with Pre/Post and DSP settings

==============================================================

Please contact PreSonus Technical Support by creating a Support Ticket at My.PreSonus.com/Support for further assistance.

>How to create a support ticket<

Was this article helpful?
0 out of 1 found this helpful
Powered by Zendesk